|
|
R/C Model Helicopters Photos and Stories
|
|
SKYDOG SPORTS
|
|
R/C Model Helicopters Photos and Stories
|
|
|
|
|
|
Gogian Yee R/C Models
|
Gogian Yee of Montebello, California sent us these photos of his R/C Helicopters and Plane. Descriptions at Bottom of Page |
|
|
|
|
|
|
|
|
|
|
|
Gogian's 700 E Converted From Nitro |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
Align TREX
450se
------------------------------
PRO 3D 325 blades
KBDD tail blades
KBDD paddles
Gorilla Gear (yellow) skids
Align Green/Blue/Black canopy
Futaba T7CHP PCM w/ R146i w/HiTec HS-65MG servos
Futaba GY401 gyro w/9650 digital servo
Align 3500kv stock motor
Align 35a ESC
Align 10a BEC - soon to be changed to CC 10a BEC to supply 6 volts for better
servo performance and speed.
Hyperion 3s 35c 11 volt 2200mah LiPos
Rhino 3s 45c 11 volt 2250mah LiPos
Anderson 45a Power Poles!
Align TREX 600 ESP w/Hacker A40 10L, 1100kv motor, 15 tooth pinion
------------------------------
PRO 3D 600 CF Blades
KBDD Yellow paddles
KBDD Yellow tail blades
Futaba 7C TX, 2.4ghz Fasst R617FS receiver w/S3152 servos
Futaba GY401 gyro w/9254 Digital servo
Castle Creations 85a HV ESC using FW version 3.20
Castle Creations 10a BEC set to 6 volts
RC Booya quick disconnects for the canopy
Flightmax 6s 25c 22 volt 5000mah LiPos
Anderson 45a Power Poles
TREX 700 Nitro FBL converted to electric
------------------------------
Align 760L FBL set to 40% on Ail and Elev gains, single Align Gyro mount pad for
the sensor
Hacker A50 14L, 540kv motor with KBDD pinion Support and KBDD Electric
Conversion motor mount/kit
Align MOD 1 150 tooth main gear & RevCo 15 tooth pinion
Kontronik 120a HV ESC using slave BEC output to Pitch servo via Y-cord to the
FBL servo pitch port to supplement power bus on the FBL side
Align 690 CF blades - will try CY 710 wide chords and/or EDGE 710s in the future
KBDD Orange tail blades
CanoMod canopy
RC Booya quick disconnects
Anderson 45a Power Poles
Grogian's Plane
|
|
|
S |
|
|
|
T |
|
|
||
|
|
|
Total Kaos
60 Nitro converted to electric (approximately 20 years old!)
------------------------------
RimFire 60 50-55-650kv outrunner BL motor turning APC 11x10 Electric Propeller
w/flow-thru Dubro Yellow spinner
Customized Rimfire motor mount with rubber vibration stand-offs
Castle Creations 125a ESC using FW version 3.2
Futaba 2.4ghz R615HS receiver
3- FPS148 Digital servos for the rudder, elevator & aileron
1- Futaba ??? retract servo for the main landing gears
2- Hitec
RS 56HB micro servos for the flaps (custom setup by me) mixed flaps with
elevator on the TX
Flying weight at ~7 lbs wet using 1- Flightmax 6s 25c 22 volt 5000mah LiPo
mounted in the nose just forward of the leading edge- Perfect balance!
Anderson 45a Power Poles
|
|
|
D |
